Qualified Products Home
660-Vehicle Detector

A ) Loop Amplifiers
(Compliance with PWWM Traffic Signals & Signs Division technical specification: Traffic Controller Assemblies Specifications, 2007 Edition).
FDOT_APL_NOAPPROVALMANUFACTURERDEVICE_DESCRIPTION
6601355080204106/24/2005Eberle Design Inc.LM222
6601355080208112/31/2008Eberle Design Inc.LMD222

B ) Loop Sealant
Two-component Polyester Loop Sealant; self leveling; permanently flexible; shall withstand corrosive effect of road salts, automotive fluids, jet fuel, gasoline and extreme weather conditions; rapid curing with extreme adhesion to concrete and asphalt
FDOT_APL_NOAPPROVALMANUFACTURERDEVICE_DESCRIPTION
6601381071401304/16/1996Durant Performance CoatingsSTAT-A-FLEX (For Asphalt or Concrete)
6601382071401304/16/1996Durant Performance CoatingsSTAT-A-FLEX (For Asphalt or Concrete)
6601381070701306/17/1986Dynatron / (3M) Bondo Corp.Bondo P-606 (For Asphalt or Concrete)
6601382070701306/17/1986Dynatron / (3M) Bondo Corp.Bondo P-606 (For Asphalt or Concrete)

C ) Video
Unless otherwise stated in the Device Description: Special Composite cable required, located under Section 632 - Signal and Interconnect Cable, item "G" Composite Cable (Power and Video); CCD Camera Mount Mast Arm Bracket, located under Section 659 - Signal Head Auxiliaries.
FDOT_APL_NOAPPROVALMANUFACTURERDEVICE_DESCRIPTION
660-015-02810/12/2011Econolite Control Products Inc.AUTOSCOPE ENCORE with TIP and TAP/connected via Parallel I/O Cable for 24 outputs and C4 Green/Red Interface Cable Assembly for 170 controllers or SDLC Cable to 2070-2E+ C12S for 2070LX controllers; 3-conductor, 18 AWG, Polyethylene Jacketed, 600V rated manufacturer approved power cable; mounted with Pelco mount AS-0175-74-120-PNC (74” tube and 120” SS cable).
660-015-02303/13/2008FLIR ITSModel VIP3D.1s with CT RDP TC650AZD65 camera and RDP OHT housing with sun shield, FLIR FC-Series ITS cameras (with lens option selected for site-specific use), or CT BCH-AZ10X30-115x camera; and FLIR ViewCom/E MAX+ Communication Board (OPTIONAL)
660-015-02403/13/2008FLIR ITSModel VIP3D.2s with CT RDP TC650AZD65 camera and RDP OHT housing with sun shield, FLIR FC-Series ITS cameras (with lens option selected for site-specific use), or CT BCH-AZ10X30-115x camera; and FLIR ViewCom/E MAX+ Communication Board (OPTIONAL)
6601372121204103/10/2003Iteris Inc. (Odetic)+/-Ext Modules/Vantage Edge2-1N
6601372121205103/10/2003Iteris Inc. (Odetic)+/-Ext Modules/Vantage Edge2-2N

D ) Current Switch
For detection of Red and Yellow traffic signal phases for use with Traffic Infraction Detectors (T I D) and any other applications that require an on/off indication of AC current flow; Operating conditions: 112 VAC within +/- 32 VAC; Off-state leakage current maximum 50 ua; On-state continuous maximum 1.0 Amps AC RMS max.; Operating Temperature: -30° C to +60° C; Six (6) turns installation conformance required with device usage; (Conformance with IACP "Performance Specifications: Red Light Camera System Module", RLCS Performance Standards, Volume 1 dated 11/29/07)
FDOT_APL_NOAPPROVALMANUFACTURERDEVICE_DESCRIPTION
N/A11/24/2010CR Magnetics Inc.CR9350-ACA

E ) Wireless Magnetometer Assembly
While inductive loop detectors continue to be the predominant vehicular detection type in Miami-Dade County, the site-specific use of alternate vehicular detection types, including the product(s) listed below, will be considered on a case-by-case basis and may be limited to further pilot-scale evaluations on Miami-Dade County roadways.
FDOT_APL_NOAPPROVALMANUFACTURERDEVICE_DESCRIPTION
660-024-00301/09/2015Trafficware Group Inc.Model VDS-POD/Limited to Vehicle Presence Detection. Cable insulation must be 600V rated. Includes Base Station, wired connection to Access Point, Sensors, and Antenna. Requires stainless steel cable mounting. Sensor installation requires the use of manufacturer provided or recommended sealant (Fabick MP-55). FDOT recommends three or more sensors for detecting motorcycles at stop bars.

F ) Microwave
While inductive loop detectors continue to be the predominant vehicular detection type in Miami-Dade County, the site-specific use of alternate vehicular detection types, including the products listed below, will be considered on a case-by-case basis and may be limited to further pilot-scale evaluations on Miami-Dade County roadways
FDOT_APL_NOAPPROVALMANUFACTURERDEVICE_DESCRIPTION
660-026-00202/27/2012Wavetronix LLCSS-200V and SS-200E (SmartSensor Advance); SS-200V or SS-200E Sensor; Click 600; Click 112 or Click 114 detector rack card(s); ss710 junction box; cables 600v insulation rated including factory-terminated drop cable ; mount with Pelco Clamp Kit (AS-3009), SH-0515 mount, and SE-0436-10 tube
660-018-00412/08/2010Wavetronix LLCSS225 SmartSensor Matrix; SS-225 Sensor; Click 600; Click 112 or Click 114 detector rack card(s); ss710 junction box; cables 600v insulation rated including factory-terminated drop cable; mount with Pelco Clamp Kit (AS-3009), SH-0515 mount, and SE-0436-10 tube

G ) Automatic Vehicle Identification
FDOT_APL_NOAPPROVALMANUFACTURERDEVICE_DESCRIPTION
660-027-00302/12/2015Digiwest LLCBlueMAC; Permanent-AC/POE
660-027-00402/20/2015TrafficCast International Inc.BlueTOAD; Solar and AC/POE



Dynatron / (3M) Bondo Corp.www.bondo.com
Wavetronix LLCwww.wavetronix.com/en/products
Durant Performance Coatingswww.durantcorp.com
CR Magnetics Inc.www.crmagnetics.com
TrafficCast International Inc.www.trafficcast.com
Econolite Control Products Inc.www.econolite.com
Trafficware Group Inc.www.trafficware.com
FLIR ITSwww.flir.com/home/
Eberle Design Inc.www.editraffic.com
Iteris Inc. (Odetic)www.iteris.com
Digiwest LLCwww.digiwest.com

HISTORY:
Addition of Durant Performance Coatings to QPL (10-28-10)
Addition of Current Switch and Wireless Magnetometer Assembly for use w/TID equipment to QPL (12-01-10)
Addition of LMD222 Loop Amplifier to QPL (10-26-11)

Last Modified on : 5/5/2017 12:55:26 PM